Drag Reducing and Increasing Mechanism on Triangular Riblet Surface

Drag reducing and increasing mechanism on riblet surface has been studied through computational fluid dynamics(CFD).Drag reduction is achieved through the optimization of riblet geometry which would affect flow structure inside riblet grooves.Force and flow structure on riblet surface are analyzed and compared with those of smooth surface based on the k-εturbulence model.Drag reducing and increasing mechanism is proved to be related to microvortexes induced inside riblets which lead to Reynolds shear stress reduction significantly and is considered to be the dominant factor resulting in wall friction reduction.Simulation results also show that the pressure drag generating from the deviation of static pressure on the front and rear ends of riblets occurs and grows exponentially with Mach number,which can cause drag increasing.Furthermore,near-wall vortical structures,Reynolds shear stress and static pressure on riblet surfaces are also analyzed in detail.     

带有引诱角色的多飞行器协同最优制导方法

考虑我方高价值飞行器面临对方拦截器拦截时,发射两枚防御器对拦截器进行拦截的情形。针对对方拦截器采用扩展比例导引律,在4个飞行器均具有一阶线性动力学特性假设下,基于最优控制理论设计了能在拦截末端施加相对拦截角的显式协同制导律。显式协同制导律将高价值飞行器和两枚防御器三者的协同考虑在内,给出了三者最优控制输入的解析解。仿真结果表明,设计的制导律能使两防御器成功拦截敌方拦截器,且在拦截末端施加一个相对拦截角。通过与只考虑两防御器协同的隐式协同制导律进行比较,可发现显式的协同制导律在控制要求和能量消耗上,要优于隐式的协同制导律。此外,还验证了在不同发射条件下的协同制导律的稳定性。     

战斗机嵌入式训练系统中的智能虚拟陪练

智能化"实虚"对抗是现代先进战斗机嵌入式训练系统的重要功能需求。自主空战决策控制技术在未来空战装备发展中扮演关键角色。将当前的功能需求和发展中的技术结合起来,得到了空战智能虚拟陪练的概念。先进控制决策技术的引入使得智能虚拟陪练能够帮助飞行员完成复杂的战术训练,而训练中真实的对抗场景为技术的验证提供了理想的环境,大量的训练数据为技术的持续迭代优化提供了保障。作为可学习和进化的空战战术专家,智能陪练在人机对抗和自我对抗中不断优化,当其具备与人相当甚至超越人的战术能力时,可应用于未来的无人空战系统。智能虚拟陪练需要具备4项基本能力：智能决策能力、知识学习能力、对抗自优化能力和参数化表示能力。对其包含的关键技术进行了分析,提出并实现了一个基于模糊推理、神经网络和强化学习的解决方案,展示了其各项基本能力及目前达到的空战水平。未来更多的模型和算法可在智能虚拟陪练的框架中进行验证和优化。     

固体燃料ATR涡轮/压气机匹配方法研究

为了获得固体燃料空气涡轮火箭发动机(SP-ATR)中涡轮和压气机的匹配工作特性,建立了涡轮和压气机的工作特性模型,根据SP-ATR转速、功率和背压平衡的工作特点,分别基于涡轮和压气机的工作环境先后采用两种不同的方法完成了二者的匹配。对比两种匹配方法得出结论:(1)基于涡轮的匹配方法与转速稳定过程一致,可确定特定飞行环境中发动机的转速;(2)基于压气机的匹配方法需要条件更少、适用范围更广,可用于特定转速调控方案下驱涡燃气流量的确定。两种匹配方法的计算结果相对Ax STREAM仿真结果的最大误差为10.75%,两种匹配方法的计算结果相差不超过8%。将建立的匹配方法应用于HARM弹自主爬升飞行过程,得到SP-ATR驱涡燃气流量的定量调控规律。     

高旋转数下45°斜肋回转通道平均换热特性研究

为了更加深入地研究涡轮叶片回转通道的换热特性,研究了高旋转数下带45°斜肋回转通道的平均换热特性。在通道进口雷诺数从10000~70000,旋转数从0~2.07的范围内,实验研究了旋转状态下,方形截面带45°斜肋U型通道径向出流与径向入流两个流程四个侧面在0°,22.5°和45°三个安装角下的平均换热系数。研究结果表明:45°斜肋增强了通道换热,减弱了旋转对换热的影响;由于浮升力作用在肋间二次流上,导致通道内外侧出现临界回流现象;转角减弱了第一通道旋转对换热的影响,增强了第二通道旋转对换热的影响,其影响在低旋转数下并不显著,在高旋转数下开始变得明显。     

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Numerical study on flow fields and aerodynamics of tilt rotor aircraft in conversion mode based on embedded grid and actuator model

A method combining rotor actuator disk model and embedded grid technique is presented in this paper, aimed at predicting the flow fields and aerodynamic characteristics of tilt rotor aircraft in conversion mode more efficiently and effectively. In this method, rotor's influence is considered in terms of the momentum it impacts to the fluid around it; transformation matrixes among different coordinate systems are deduced to extend actuator method's utility to conversion mode flow fields' calculation. Meanwhile, an embedded grid system is designed, in which grids generated around fuselage and actuator disk are regarded as background grid and minor grid respectively, and a new method is presented for ‘donor searching' and ‘hole cutting' during grid assembling. Based on the above methods, flow fields of tilt rotor aircraft in conversion mode are simulated, with threedimensional Navier–Stokes equations discretized by a second-order upwind finite-volume scheme and an implicit lower–upper symmetric Gauss–Seidel(LU-SGS) time-stepping scheme. Numerical results demonstrate that the proposed CFD method is very effective in simulating the conversion mode flow fields of tilt rotor aircraft.     

亚声速进气道设计敏感参数仿真分析

对不同气动布局的两种亚声速进气道建模,并针对两种进气道的敏感参数进行分析。通过对背部双发布局飞机进气道的隔道高度和喉道设计马赫数参数的研究可知,隔道高度增大或者喉道设计马赫数减小,使得进气道出口总压恢复系数增大,增量约0.5%。而对背部单发复杂形状进口(M型进口)布局飞机进气道的喉道形状研究显示,喉道形状越接近进口形状,进气道性能越好,较其他喉道形状进气道,M型喉道进气道出口总压恢复系数最高,最大增量约为1.5%。     

飞机机头附近液态水含量分布规律的数值研究

在飞行器飞行过程中,安装在机头上的各类传感器结冰会对飞机的飞行安全产生不利影响。而液态水含量是影响飞机结冰的重要参数,为了更好地进行传感器结构及布局设计,对机头附近液态水含量分布规律进行数值研究。采用计算流体力学方法对飞机飞行时的空气-过冷水滴的稀疏两相流场进行数值模拟,通过求解N-S方程获得空气流场,采用欧拉法求解水滴运动场得到水滴运动轨迹。分析在不同来流马赫数、来流迎角及液滴直径等条件下,机头关键截面上广义水滴遮蔽高度的变化及机头关键位置上液态水含量的变化规律,研究不同状态参数对液态水含量分布的影响。结果表明:水滴遮蔽高度及浓度增加区范围随马赫数增大而增加,迎角的变化对机头上下表面液态水含量分布产生相反的影响。     

基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。